API INSPECTION SERVICES — UAE
Remote document review and on-site source inspection for ADNOC supply chain and ASME-certified fabricators in the UAE. Jebel Ali, Abu Dhabi, and international supply chain coverage.
Why UAE Projects Require Independent Third-Party Inspection
The UAE — and Abu Dhabi in particular — has built one of the world’s most technically demanding oil and gas sectors under ADNOC. Equipment entering ADNOC facilities and the broader UAE industrial sector is required to meet ASME VIII and B31.3 fabrication standards, with ADNOC specifications defining additional inspection and documentation requirements.
The Jebel Ali Free Zone (JAFZA) and Abu Dhabi industrial areas host a concentration of ASME-stamped fabricators producing pressure vessels, heat exchangers, and piping for both domestic UAE projects and international export. METALFAB, NASH Engineering, and Berg Industries are among the ASME U-stamp holders operating in these zones.
Independent TPI verifies that the fabrication executed at these shops actually followed the code the U-stamp represents — material traceability, WPS compliance, dimensional accuracy, and NDE record integrity. For international operators and EPC contractors procuring from UAE fabricators, this verification is the mechanism that closes the quality assurance gap between the purchase order and the delivered equipment.
What Norman QC Provides
Remote Document Review
- -WPS and PQR review against ASME Section IX
- -ITP review and hold point designation
- -MTR verification against material specification
- -NDE procedure and record review
- -ADNOC specification compliance verification where applicable
On-Site Source Inspection
- -Material traceability verification at hold points
- -Dimensional inspection against approved drawings
- -Weld quality observation and NDE sign-off
- -Pressure test witnessing
- -Pre-shipment inspection and shipping release
Applicable Standards
| Code | Application |
|---|---|
| ASME Section VIII Div.1 / Div.2 | Pressure vessel fabrication |
| ASME B31.3 | Process piping |
| ASME Section IX | Welding qualification |
| ADNOC Specifications | Operator requirements for Abu Dhabi projects |
| TEMA | Heat exchanger mechanical design standards |
Key Facilities and Supply Chain
UAE pressure equipment fabrication is concentrated in two areas: Jebel Ali Free Zone (JAFZA) in Dubai, which hosts a range of ASME U-stamp authorized fabricators serving both domestic UAE projects and export markets; and the Abu Dhabi industrial zone, which supplies ADNOC and its downstream affiliates. Notable ASME-authorized fabricators in the UAE include METALFAB (Abu Dhabi), NASH Engineering FZCO, and Berg Industries. For operators procuring equipment for UAE projects from fabricators in other countries — India, China, Korea — Norman QC performs source inspection at the fabrication location and delivers documentation aligned with the UAE project requirements.
How It Works
Remote Document Review
WPS/PQR, ITP, and MTR packages reviewed against ASME codes. Documents approved before production begins.
On-Site Hold Point Visits
Focused visits at critical fabrication hold points. Signed report at each stage with photographs and non-conformance records.
Reports and Shipping Release
Pre-shipment inspection and signed shipping release. Complete PDF report package for client QC records and ADNOC submissions.
FAQ
What ADNOC inspection requirements apply to third-party fabrication?
ADNOC (Abu Dhabi National Oil Company) specifies inspection requirements through its company specifications and approved vendor lists. Equipment entering ADNOC facilities must comply with ASME VIII and B31.3 as the base fabrication codes, with ADNOC-specific technical specifications overlaying those requirements where applicable. Third-party inspection verifies that the fabricator's WPS/PQR, ITP, and material documentation satisfy both the ASME code requirements and any ADNOC specification requirements referenced in the purchase order.
Does NormanQC cover both remote review and on-site visits in UAE?
Yes. Remote document review — WPS/PQR, ITP, MTR, and NDE records — is performed from Edmonton with documents submitted electronically. On-site source inspection visits are coordinated at fabrication facilities in the UAE, including Jebel Ali Free Zone and Abu Dhabi industrial areas, at defined hold points aligned with the fabrication schedule.
What is the typical scope for a UAE pressure vessel source inspection?
For a UAE-fabricated pressure vessel, the standard scope is: remote review of WPS/PQR, ITP, and material documentation before fabrication begins; one or two on-site visits for material traceability verification, dimensional checks, and NDE hold point sign-off; and a pre-shipment inspection with shipping release. The total report package constitutes the independent QC record for the equipment.
Which UAE fabricators does NormanQC work with?
Norman QC coordinates source inspection at ASME U-stamp authorized fabricators in the UAE, including facilities in Jebel Ali Free Zone (JAFZA) and the Abu Dhabi industrial zone. These fabricators supply ASME-coded pressure vessels, heat exchangers, and piping for ADNOC projects and international export. Norman QC works with whatever fabricator the client's purchase order designates.
Can NormanQC support UAE projects where the equipment is fabricated elsewhere?
Yes. For projects where equipment is being supplied to UAE operators but fabricated in India, China, Korea, or other locations, Norman QC performs source inspection at the fabrication site and delivers reports aligned with the UAE client's project requirements. This is the most common model for large-scale procurement programs.
WORKING ON A UAE PROJECT?
Contact for scope and availability. Remote document review begins immediately. On-site inspection coordinated with UAE fabrication schedule.